We live in a time when a natural phenomenon that we all know as global warming is occurring, but on top of that there is gradual deforestation and pollution in general all over the world.
This is what obliges us as human beings to protect the environment. However, sometimes we have to make the difficult decision to cut down a treeeither for lack of space, or for security reasons or that of a neighbour.
Contents
Ways to dry out a tree
If it is true that we have a tree trunk in our garden that is generating new shoots, we must remove it, because it is possible that it will continue to grow. For this we show you some methods that we can use for this task.
Use Epson salt or rock salt
The first thing we have to do is buy Epson salt or rock salt, this being a fairly simple way to remove a tree stump if you don’t have a lot of money. However, we must bear in mind that if we use this method it will take us a few months for the stump to die, so it is not the best alternative if we want to eliminate it as soon as possible.
We must not use regular salt, as it is quite harmful to the soil where the stump is. We have to use the Epson salt or 100% rock salt without having added any ingredients, so that we have the security that the ground that surrounds the stump does not undergo alterations.
If it is a strain that has a hard time dying, we can try a chemical or herbicide that has glyphosate or tricoplir in its components instead of salt. Sure, the herbicide will remove the trunk of the tree as quickly as possiblebut we must bear in mind that it will kill the roots of the plants or trees that are around.
Related article:
What are selective herbicides?
We must drill a pattern of holes over the entire surface of the trunk so that the solution can enter properly.
These holes must have a measure 1.4 to 2.5 cm wide and at least 20.3 cm deep or unlike it 30.5 cm if our drill is long enough and it is that a deep penetration is what will give us the security that the solution with the salt can reach all the roots of the trunk and if the roots of the trunk are too big, we have to drill them in the same way.
Then we fill each of the holes with the salt and we cover with wax. For this, we fill each hole with ¾ of Epson salt or rock salt, without forgetting the holes that we have also made in the roots of the trunk.
Then we light a common candle and we add wax in the holes to be able to seal thembeing very important that we make sure that the salt is in the same place, instead of being scattered around the patio, since an excess of salt can be harmful to the roots of other plants that we have in the garden.
Now we cover the trunk and to do it put up a plastic sheet, a garbage bag or any other object to cover the boot. This way it will dry out much faster because it has no sun and gets rainwater, so the shoots won’t be able to continue feeding.
Cover the trunk to avoid direct sunlight
The first step is to cover the trunk, it is an inexpensive technique, but can be very time consuming. By this we mean dry the trunk slowly taking along all the basic necessities.
For that we put a dark colored tarpaulin or a plastic bag on it so that it cannot receive either sun or water. Then we only have to wait 3-6 months, because during this time the trunk dries slowly, having to check from time to time to see how the process is going. We will notice that the trunk will begin to rot and crumble.
We must cut off any shoots growing around the trunk and it is that if we cover the trunk it will grow something else, but until it is dry we must cut all the shoots that appear at the base of the trunk.
Another solution we can use for this is paint them with a brush containing triclopyr.
Other techniques that we can use to cut down a tree
In this first method we have to use the drill
We start by making holes with the drill that do not exceed half an inch, taking into account that we must follow the circumference of the trunk. Then we have to make the holesfilling with a fertilizer with a high nitrogen content.
Over the days, in the holes a fungus will grow which will decompose the woodsomething that can take about four or six weeks.
In this second method we have to use nails
In the second method to delete a tree, we have to use copper nails.
We need a large number of copper nails and if possible large ones. Only they must be nailed to the trunk of the tree, something that will cause the fungus to enter the tree to decompose it.
In this third method we have to use a chainsaw
And finally, the best method we can use to eliminate a tree, whatever the reason, is to use a chainsaw.
For this task, all we need to do is make a size assessment of the tree, as a fall could cause major damage to any nearby property. to be a fairly simple task It is not necessary that we leave this activity in the hands of an expert, however, we must take into account certain security measures.
Related article:
How to Cut a Garden Tree Using a Chainsaw