Power Requirements Requires power between 15 and 20 HP per chisel.
What is a subsoiler and what is it used for? Function main • Soil cracking breaking the compacted layers without inverting the profile. They must work at least 10 cm below the layer to be broken. The soil is broken in a V from the bottom of the furrow to the surface.
What is Subsolar Soil? Remove the Usually I below the topsoil, or plow deep enough without turning the soil.
What function does the basement plow perform? The basement plowor subsoiler, it is a plow suitable for the basement, it is i.e. working in deeper soils which need to be removed due to: need to break up layers hardened by traffic. for increased fertility Usually I and humidity.
When to pass the subsoiler? This is best done immediately after harvesting, either maize or after crops such as wheat or rape (in summer), when soils have low moisture content.
What are the types of subsoilers?
We can divide them into two groups:
- Powered. Alternative arm moved by a system of shafts and gate driven by an oscillatory movement caused by connecting rods.
- Not powered. By rubber blocks, fixed with a tree-shaped bolt.
Contents
How much HP is needed per Chisel Spike? – Related issues
How many resumes does a subsoiler need?
Conditions of use and performance The power required by the tine varies between 35-45 HP (28-33 kW) for 30 cm working depth, up to 55-65 HP (45-48 kW) for 70 cm. Working speeds should be maintained between 3.0 and 5.0 km/h, achieving a yield of 0.65 to 0.85 on the plot.
How is subsoiling done?
The basement or scarified This technique consists of passing a machine over the ground subsoiler 5-point scarifier; work at a depth of 35-40 cm, in addition to covering a width of 1.5-2.0 meters (working width of the equipment).
How big is a subsoiler?
Their working widths vary from 120cm to 320cm and can be adjusted to get the right working width for your tractor and working area. The working depth of subsoilers It can be 70cm to 85cm.
What are the parts of a subsoiler?
subsoiler
- subsoiler. …
- Hooking system. …
- Wheel. …
- Chassis or sash. …
- arms or legs…
- Scissors or bars.
How deep is the basement?
Deep soils have a meter or more to reach a boundary layer. Moderate depths are less than one meter but greater than 0.60 m. The shallow soils measure less than one meter but more than 0.60 m. Shallow soils are less than 0.25 m.
Why is the land plowed?
Plow increases porosity, which promotes growth of plants, although water is lost when the soil is disturbed for evaporation and something of Usually I for erosion and possible rain wash away the nutrients and fertilizers that may have been applied to the soil, generating losses.
What type of plow is best?
The plow The disc type is also useful for tillage, but unlike the mouldboard, the disc type is better in hard and rocky soils or soils with large remains of roots, because it works according to its weight.
How to improve compacted soil?
A totally biological method to improve the structure of a Usually I and increase its porosity by growing plants that cover a large area at a reduced cost. When they grow, their roots dig galleries which remain intact (if they are not plowed) until the next harvest.
How to improve soil aeration?
Wetting agents improve infiltration and water reaches deeper levels of the Usually I. They also allow microorganisms to burrow deeper. By digging, they improve the soil aeration and allow water to infiltrate lower, which promotes root development.
What are the disadvantages of the plow?
These are the main plow disadvantages:
- Damage to the existing microflora in the soil is caused. …
- Creation of the plowing crust. …
- Increased number of tillage steps. …
- Greater energy and economic consumption.
What is basement work?
The works of plowing The most common primaries in many parts of Mexico are subsoil and fallow. Subsoiling is the operation that consists of breaking up the soil without turning it over or changing its position up to 80 cm deep. it’s done with a plow basement or subsoil plough.
What is the subsoil in agriculture?
It is the tool indicated for lands that have a long cultivation period, where the soil is compacted between 20 and 40 cm deep and does not allow adequate infiltration of water, affecting root growth, for this and many more benefits. , which we have every confidence that our…
What is Paratile?
Vertical tillage equipment for loosening deep layers.
How much HP does a portcullis need?
Consumption unit 36 86 HP.
How many HP per plow disc?
Plow of discs It consists of 3 to 4 discs 24″ or 26″ X 1/4” thick disk, with a working depth of disk from 15 to 25 cm. Power requirement for equipment from 80 to 100 hp engine.
What are the types of plows?
The plow It is a widely used agricultural tool in various soil conditions.
- The plow it is probably the oldest tool or tool used in agriculture, also providing a long useful life for the farmer. …
- three differ types: mouldboard, disc and rotary.
What are the types of streaks?
Types of the dredges discs
- Integrals. These are the ones that hitch the tractor by three points. They are suspended in transport. …
- Slide. They hook into the traction of the tractor by means of a drawbar.
What is vertical tillage?
The vertical plowing it is a system of guiding principles that maximizes yield by increasing water infiltration, root development and nutrient uptake.
What are the parts of a subsoiler?
subsoiler
- subsoiler. …
- Hooking system. …
- Wheel. …
- Chassis or sash. …
- arms or legs…
- Scissors or bars.
What is the agricultural subsoil?
The basement This is the operation that consists of breaking up the soil without turning it over or changing its position up to 80 cm deep. This is done with the basement plow or subsoiler plow. Apply fertilizers, insecticides, etc.
What are the types of plows?
The plow It is a widely used agricultural tool in various soil conditions.
- The plow it is probably the oldest tool or tool used in agriculture, also providing a long useful life for the farmer. …
- three differ types: mouldboard, disc and rotary.
What is fallow in agriculture?
This concept assumes rest between sowing and cultivation, an agricultural process to allow the qualities of the soil not to wear out. The rest periods are usually every two or three years, in this way the soil recovers its nutrients and in the next planting it will bear the best fruits.